Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateFAAC Electric Gate Repair in New York: What to Know First
FAAC electric gate repair in New York typically costs $240 – $680 for most common failures, and we stock the parts that fail most often so many jobs are finished the same day. As an independent FAAC service provider, we handle everything from dead keypads and fried control boards to actuators that hum but won’t move. We quote the job in writing before we turn a single bolt, and every repair carries the 365-Day Done Right Promise in writing.
This page is for homeowners in New York who own a FAAC swing or slide gate and need someone who actually knows the brand. If your gate stopped responding to remotes, beeps but won’t open, or opens halfway and reverses, call (845) 259-0242. A live person answers, day or night.
How FAAC Products Fail – and How We Fix Them
FAAC builds solid operators, but they’re not flawless. These are the five failures we see most often on New York properties, and they tend to be brand-specific, which is why a generic gate tech misses them.
- Dead display on E024S and S800H control boards after a storm. New York gets real electrical weather, and a nearby lightning strike or a power surge will take out a FAAC board’s transformer before the breaker ever trips. The homeowner sees a dead keypad and assumes the worst. We bench-test the board, replace the surge-damaged component when possible, or swap in a new board and add a surge suppressor so it doesn’t happen again next summer.
- Humming actuator on FAAC 400-series swing operators that won’t move the leaf. That hum is the motor straining against a seized worm gear or a worn bushing inside the actuator housing. The motor’s fine, but the drivetrain has given out. We rebuild the actuator when the housing is still sound, or replace it with a new FAAC 400 actuator when it’s beyond saving. It’s a half-day job either way.
- Gate opens a few inches and reverses on FAAC C720 and C721 slide operators. In New York, this is usually a failing encoder or a magnetic limit switch picking up false readings from rust accumulation on the rail. The board thinks the gate hit an obstruction and backs off. We clean the rail, test the limit switch with a diagnostic tool, and recalibrate the travel limits. If the encoder’s failing, we replace it before the board starts cooking itself trying to make sense of bad signals.
- Keypad and remote work, but the gate ignores them at night. FAAC photocell safety sensors are sensitive to condensation and temperature swings, and New York winters love to fog them up. We clean the lenses, check the wiring for moisture intrusion, and reposition the sensors if they’re getting false obstruction readings from reflected light off wet pavement. Sometimes a simple alignment is all it takes; other times the sensor pair gets replaced.
- FAAC hydraulic operators leaking fluid and losing power in cold weather. Older FAAC 750 and 760 hydraulic swing units run on hydraulic oil, and when New York temperatures drop below freezing, old seals shrink and start weeping. The gate moves slower, then stops holding position. We replace the seals, refill with the correct FAAC-spec hydraulic fluid, and pressure-test the system. It’s the difference between a $350 reseal and a $1,400 operator replacement if the leak’s ignored.
Styles & brands we work with
Our FAAC Electric Gate Repair Process
Here’s how a FAAC repair goes from the first call to the final test, done the Kingswell Way.
- 1
You call, we answer. A live person picks up at (845) 259-0242, 24/7. You describe what the gate’s doing – or not doing – and we give you a ballpark range over the phone.
- 2
We show up in the window we gave. Our FAAC tech arrives in a Portcullis uniform, introduces himself, and walks the gate with you before touching anything.
- 3
We diagnose in front of you. We test the board, actuator, sensors, and wiring. We’ll tell you what failed, why it failed, and what it’ll cost to fix, in writing, before we start.
- 4
We use the right parts. For safety-critical components like control boards and sensors, we stick with genuine FAAC or OEM-equivalent parts. For wear items like bushings, seals, and hardware, we use quality aftermarket options when they match or exceed the original spec, so you’re not paying a brand-name markup for a capacitor.
- 5
We repair, test, and clean up. We run the gate through full open-close cycles, recalibrate limits and force settings, and test every remote and keypad you hand us. Then we sweep up the metal shavings and old parts.
- 6
You get it in writing. The invoice shows the exact work done, the parts used, and the 365-Day Done Right Promise: if the repair fails within a year, we come back and fix it at no charge. No fine print, no re-diagnosis fee.
What FAAC Electric Gate Repair Costs in New York
Most FAAC repairs in New York fall into these ranges, parts and labor included:
- Limit switch or encoder replacement on FAAC slide operators (C720, C721): $260 – $410
- Control board replacement (E024S, S800H, 455D): $380 – $680 depending on the board generation
- Actuator rebuild or replacement on FAAC 400-series swing operators: $450 – $900 per leaf
- Photocell sensor pair replacement and realignment: $180 – $320
- Full diagnostic call (no repair needed): $90 – $140, credited toward the repair if you proceed
What moves the price is the operator model, whether we’re rebuilding or replacing, and whether the gate is a single or double leaf. Hydraulic units cost more than electromechanical ones, and gate length matters on slide operators because it dictates the drivetrain spec. We give you a written price before any work starts, and estimates are always free. Call (845) 259-0242 and ask for a real number.
See the difference
Before
After
Before
After
Before
AfterWhy New York Homeowners Call Portcullis Gate Repair New York for FAAC Work
Plenty of gate companies in New York will say they service FAAC. What they mean is they’ll look at it and figure it out as they go. Our techs have been working on FAAC operators since 2008, longer than most shops have been in business. That means we recognize a failing limit switch on a C721 before the board starts throwing error codes, and we know when a 400-series actuator is worth rebuilding versus replacing without running up your bill.
We also service the brands around your FAAC, LiftMaster, Mighty Mule, Ghost Controls, and DoorKing, so if your property has a mix of operators across different entries, one crew handles all of it. Every Portcullis location is independently owned and operated, but held to the same written Kingswell Guarantee: the price before the work, the arrival window, the clean job site, and the repair in writing for 365 days. That’s not a franchise slogan. It’s stamped on every invoice.
FAQs
If your FAAC operator is still under the manufacturer’s warranty, yes, opening the housing or swapping parts yourself can void it. Even if the warranty period has lapsed, a wrong diagnosis can turn a $200 limit switch repair into a $600 board replacement. Our recommendation is always diagnosis first. We’ll tell you exactly what failed and what it costs before any work starts.
For control boards, safety sensors, and other components where performance and code compliance matter, we use genuine FAAC or OEM-equivalent parts. For wear items like seals, bushings, capacitors, and drive hardware, we use quality aftermarket parts when they meet or beat the original specification. We’ll always tell you which is which before we order anything.
Many FAAC electric gate repairs in New York are same-day jobs because we stock the most common failure parts on our trucks: limit switches, capacitors, photocells, and fuses for the popular FAAC models. If we need a specific board or actuator for an older unit, we’ll order it and get you on the schedule immediately, usually within one to two business days. Call (845) 259-0242 and tell us what the gate’s doing. We’ll give you an honest timeline, not an optimistic one.
The simple math is this: if the operator is under 10 years old and the repair is under $700, repairing almost always makes sense. If the unit is 15-plus years old and the failure is a seized actuator or a fried main board on a discontinued model, replacement might be the smarter long-term move. We’ll tell you straight, because we don’t make more money steering you wrong. If you’d rather replace, we work with FAAC’s current lineup and can match the right operator to your gate’s weight and cycle rate.
Every repair we do, including all FAAC electric gate repair in New York, carries our 365-Day Done Right Promise in writing. If the repair fails within one year, we come back and fix it at no charge. No service fee, no parts charge, no argument. That’s the Kingswell Guarantee, and it’s printed on every invoice.
Call Portcullis Gate Repair New York for FAAC Electric Gate Repair
If you own a FAAC operator in New York and it’s giving you trouble, call (845) 259-0242. Dean Prescott and the crew will tell you what the gate is doing – or not doing – and give you a real number before we hang up. Free estimates, a written price before any work starts, and a live person on the line 24/7.
Written by Dean Prescott, Owner, Portcullis Gate Repair New York at Portcullis Gate Repair New York, serving New York and nearby areas.