Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateGate Company in New York, NY
Gate repair in New York, NY rarely looks like it does anywhere else. Most jobs here involve steel or wrought-iron gates on brownstone stoops, areaways, and service entrances, and the city’s density puts those gates directly against the sidewalk. Pedestrians lean on them, cyclists clip them, delivery carts bounce off them, and street vibration works every hinge and weld loose over time. Coastal humidity and salt air add steady rust, and winter freeze-thaw cycles throw tracks and hinges out of alignment. When a gate stops latching or a hinge starts dragging, the security and liability stakes are higher than in a suburban driveway. Call (845) 259-0242 and we’ll put the price in writing before any work starts.
Why New York Homes Are Different
New York’s housing stock shapes the work before we touch the gate. Pre-war walk-ups and post-war high-rises often use steel or wrought-iron gates on stoops, areaways, and service entrances. Brownstones and townhouses frequently have original ironwork that is decades old – scrollwork, spear finials, and hinges that were forged by hand. When that ironwork fails, repairing it often means matching the existing pattern, not swapping in something off a shelf. In many brownstone neighborhoods, areaway gates are reviewed by the city’s Landmarks Preservation Commission, so a replacement or repair has to match the original design closely enough to pass district review.
Climate is the second factor. Neighborhoods near the water – especially along the Hudson River and the East River shorelines – see accelerated rust on gate frames and hardware. Salt air eats powder coating and gets into hinge barrels and latch mechanisms. Freeze-thaw cycles are also real: water gets into hinges and tracks, freezes at night, and expands. The result is seized hinges, misaligned tracks, and gates that will not close in January unless someone forces them, which usually bends the frame. We see the same pattern every winter in New York: a cold snap, then a wave of calls for gates that suddenly will not latch.
And then there’s the density itself. A gate in a brownstone areaway is the only thing separating a family from the sidewalk. Pedestrian traffic, constant cycling, and street vibration subject these gates to impacts and wear that suburban gates never see. Repairs here are as much about security and liability compliance as they are about function – a gate that does not close properly is an open invitation and a liability.
Styles & brands we work with
Our Main New York Services
Most New York homeowners call us for three things: a repair on an existing gate, a full gate installation when an old one is beyond saving, and electric gate repair when an operator or opener stops working. Each has its own page with local pricing, what the job includes, and what to expect.
Gate Repair in New York
Gate Repair in New York covers the most common failures we see in the city: seized hinges, rusted-through frames, bent top rails, broken locks, and gates that sag and drag on the sidewalk. Many brownstone and townhouse gates are original ironwork, and when a hinge or scrollwork section fails, the repair often involves fabrication to match the existing pattern – especially in landmark districts where the review board expects it. We write the price before any work starts and back every repair with the 365-Day Done Right Promise.
Gate Installation in New York
Gate Installation in New York is for gates that are too far gone to repair safely, or for building owners adding a gate to a stoop, areaway, or service entrance that does not have one. In New York, installations often have to work around landmark district review, tight clearances on narrow sidewalks, and existing masonry or brownstone steps that we will not damage. We measure, quote in writing, and schedule the work so the gate is fabricated to fit the opening and the historic context.
Electric Gate Repair in New York
Electric Gate Repair in New York handles operators, openers, keypads, safety loops, and access-control issues on gates that open automatically. Many Manhattan and outer-borough buildings use electric gates with intercom or keypad entry, and when the operator fails, the gate either will not open or will not stay closed – either way, it is a security and access problem. We service nine major gate-operator brands, including LiftMaster, FAAC, BFT, and Linear, and we diagnose the operator before quoting the repair.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Brands We Service in New York
Our technicians are certified on nine major gate-operator brands, including LiftMaster, FAAC, BFT, and Linear. We stock common parts for those systems locally, which means most New York repairs do not wait on a part to ship across the country. See our brands for the full list.
See the difference
Before
After
Before
After
Before
AfterPricing for Gate Company in New York, NY
New York gate work is quoted flat, in writing, before we touch a single bolt. Here are the price ranges we most often quote in the city:
| Service | Typical range in New York |
|---|---|
| Hinge repair or replacement (steel or wrought iron) | $180 – $450 |
| Gate latch or lock repair | $140 – $320 |
| Sagging gate frame correction | $260 – $600 |
| Swing-gate actuator swap (parts and labor) | $520 – $1,150 |
| Gate operator control board replacement | $310 – $680 |
| Remote or keypad reprogramming | $90 – $220 |
| Track realignment (slide or cantilever gate) | $220 – $520 |
| Areaway gate repair with pattern-matched fabrication | $450 – $1,200 |
| Full manual gate installation (steel or iron, no operator) | $1,800 – $4,800 |
| Full electric gate installation (including operator) | $3,200 – $7,500 |
What pushes a New York quote toward the top of these ranges is usually fabrication – matching original scrollwork or ironwork for a landmark-district building takes time and a shop, not just a truck. Coastal rust damage and seized hardware from freeze-thaw cycles also add labor when we have to cut out old fasteners and rebuild hinge mortises. Whatever the number, it is written down and agreed before work begins, and it does not change at the door.
Neighborhoods We Serve in New York
Our crews work across all five boroughs, from Brownstone Brooklyn and the Upper West Side to Queens and Staten Island. We also serve the neighborhoods below and many more. Response time for most gate repair calls in the city is same-day or next-day, depending on the time of year – winter freeze-thaw spikes keep our schedule busiest.
- Park Slope
- Upper East Side
- Aspen Grove
- Riverdale
- Forest Hills
Service Area – Cities Near New York
Beyond the five boroughs, we serve nearby areas including Manhattan, NY, Long Island City, NY, Jackson Heights, NY, and Middle Village, NY. If you are unsure whether your building falls in our New York service area, call us and we will confirm it in under a minute.
Serving New York, NY - Our Local Coverage Area
We’re based in the New York area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs About Gate Company in New York
Most repair calls in New York get a same-day or next-morning arrival window, depending on the season and the neighborhood. A live person answers the phone 24/7, so you will not wait on a callback queue. Call (845) 259-0242 and ask for the earliest real window.
In many landmarked brownstone neighborhoods, yes. The Landmarks Preservation Commission reviews areaway gates and stoop ironwork in designated historic districts, and the repair or replacement usually has to match the existing pattern. We handle fabrication that matches the original design, which is typically what the district review requires.
The price is quoted in writing before any work starts, and that written price does not change unless you approve a change in writing. We do not quote one number on the phone and a different one at the door. The price, the arrival window, and the guarantee go on the invoice, and the guarantee runs 365 days from the date of repair.
If your gate is sagging, seized, or refusing to latch, call (845) 259-0242. A live person answers, we will schedule a real arrival window, and you will get the price in writing before a single bolt is turned.
What happens when you call
- 1A real person answersNo phone trees - talk to a local gate repair pro.
- 2You get an upfront price rangeHonest numbers before anyone is dispatched. No surprises.
- 3We come out and measureLicensed & insured, at a time that suits you - the visit and the quote are both free.
- 4You get the price in writingLine-itemed, yours to keep, and nothing starts until you say go.
What New York Customers Say
"Gate was dragging and screeching across the driveway. I figured I'd need a whole new setup. He adjusted the track and rollers and it was a fraction of what I expected. Honest work."
- Omar Haddad"Our intercom and gate motor both quit. They fixed the whole system in one visit and explained the warranty clearly. On time, polite, and tidy. Can't ask for more."
- Yvette Marchetti"Our driveway gate stopped halfway and wouldn't close, which is a problem when it's the only thing between the street and the yard. They came out same day, replaced the motor, and it's smooth again."
- Leonard Pace